|  | Ready Made Handrail kits Sizes B & C
Ready made posts with railing base - These include End post, Mid post, Corner post and 'P' post. Plus ready cut horizontal twin rails for posts at 1.5 metre centres |
|
 | Tubeclamp 101 Short Tee
Typical use on straight and level guardrails to connect the upright to the top rail or end or mid rail
to the upright. Tubes cannot be joined inside a 101, to join tubes inside the fitting use the 104.
Normally used in conjunction with the 125 fitting.
£2.60 |
|  | Tubeclamp 104 Long Tee
Typical use on straight and level guardrail to connect the upright to the top rail. Tubes can be
joined inside the 104 fitting. Normally used in conjunction with the 119 fitting.
£3.88 |
|
| |
|  | Tubeclamp 125 90 deg. Elbow
Typical use on straight and level guardrail to connect the top rails to the upright. Normally used
in conjunction with the 101 fitting. This fitting can also be used to create a 90° tube bend.
£3.08 |
|
 | Tubeclamp 128 3 Way 90 deg. Elbow
Typical use on straight and level guardrail to connect the 2 top rails to the upright at a 90° corner post.
Normally used in conjunction with the 116 fitting.
£4.33 |
|  | Tubeclamp 129 Adjustable Short Tee 30deg. - 60deg.
Typical use is on steeper slopes or stairs as a tee connector with an angle between 30° & 60° with the
upright remaining vertical. This fitting does not allow the through tube to be joined inside the fitting.
Normally used in conjunction with the 130 fitting.
£3.67 |
|
 | Tubeclamp 131 Wall Flange
This fitting can be used for terminating cross rails to walls etc., it can also be used as a base plate for
non-load bearing systems such as a bench or chair.
THIS FITTING IS NOT TO BE USED AS A BASE PLATE FOR GUARDRAILS OR DEPENDANT STRUCTURES.
£3.04 |
|  | Tubeclamp 132 Railing Base Flange
A structural base plate for all applications of vertical posts. In guardrails the fitting should be positioned
with the base holes at 90° to the line of the guardrails to give maximum strength.
£5.52 |
|
|  | Tubeclamp 134 Cast-in Ground Socket
Typical use is as a base for a removable upright that can be removed without leaving obstructions. The
tube is held in place by the setscrew. The casting hole should be a minimum 300mm x 300mm x 300mm.
£10.26 |
|
 | Tubeclamp 135 Clamp-on Tee
Typical use is for adding to an existing inline structure without having to dismantle the original structure.
£5.24 |
|  | Tubeclamp 138 Gate Eye
Female section of a two part gate hinge. Normally used in conjunction with the 140 fitting. (For heavy
or wide gates use a 147,101 &179 to construct the gate hinge. See page 14 of Tubeclamps brochure for details).
£2.85 |
|
 | Tubeclamp 140 Gate Eye
Male section of a two part gate hinge. Normally used in conjunction with the 138 fitting. (For heavy
or wide gates use a 147,101 &179 to construct the gate hinge. See page 14 for details of Tubeclamps brochure for details).
£3.08 |
|  | Tubeclamp 143 Handrail Bracket
Typical use is a wall mounting handrail bracket, this fitting can also be used to hold in place kicking
flats on guardrails or display board on exhibition displays.
THIS FITTING IS NOT TO BE USED AS A BASE PLATE FOR GUARDRAILS OR DEPENDENT STRUCTURES.
£3.76 |
|
 | Tubeclamp 144 Railing Side Support Vertical Base
Typical use is as an offset structural side palm fixing for either straight or sloping guardrails. The tube
is unable to pass through the standard fitting, should this be required then the base must be reamed
out.
£6.73 |
|  | Tubeclamp 146 Side Palm Fixing
Typical use is as a side palm fixing for the upright on either straight or sloping guardrails keeping the
upright as close as possible to the slope or stairs. The tube is unable to pass through the standard
fitting, should this be required then the base must be reamed out.
£5.36 |
|
 | Tubeclamp 147 Internal Swivel Tee
Typical use is for offset variable angle sloping guardrails used in conjunction normally with a 101 fitting.
This fitting eliminates the need for specialised angle fittings such as the 126 or 127.
£3.99 |
|  | Tubeclamp 148 Short Swivel Tee
Typical use is on level guardrails to create a corner at other than 90° with an upright. Creates angles
between 85° & 235°. When using the 148 fitting the top of the upright needs to be closed using a
133 end cap. IMAGE SHOWS TWO FITTINGS
£3.76 |
|
 | Tubeclamp 149 Sleeve Joint
Inline external connector for joining two tubes together in a run. For an inline joint that is the same
diameter as the tube the 150 fitting should be used. Not recommended as structural joint.
£3.08 |
|  | Tubeclamp 150 Internal Joint
Inline connector for joining two tubes together using medium gauge tube. It must never be used as a load bearing joint.
£2.69 |
|
 | Tubeclamp 158 Four Way Cross with Centre Tube
A four way cross for joining tubes together in the centre of a structure. The fitting allows the upright to
pass through the centre with the cross rails joining at 90° to the upright.
£6.04 |
| |
|  | Tubeclamp 167 Double Swivel Combination
Double in line swivel connector. Typical use is on sloping guardrails. This fitting combines 1 x 167M & 2 x 173F. The swivels can travel in approximately 85° from the horizontal in both vertical directions. AN ENTIRE STRUCTURE SHOULD NOT BE BUILT USING SWIVEL FITTINGS ONLY
£7.87 |
|
 | Tubeclamp 167M Double Male Section of Swivel
Double male fitting with the connection lugs at 180° to each other. This fitting can also be used to retain
display panels etc. in place. THIS FITTING IS NOT DESIGNED TO WITHSTAND
LATERAL LOADINGS
£2.96 |
|  | Tubeclamp 170 Mesh Panel Clip Single
Single mesh panel clip. Typical use is for retaining weldmesh panels into guardrails. To correctly retain the weldmesh panel using this clip the panel should be framed with an 8mm bar. Note - Dimension C can be increased by up to 10mm
£1.44 |
|
 | Tubeclamp 171 Mesh Panel Clip Double
Double mesh panel clip. Typical use is for retaining weldmesh panels into guardrails. To correctly retain
the weldmesh panel using this clip the panel should be framed with an 8mm bar.
Note - Dimension C can be increased by up to 10mm.
£1.92 |
|  | Tubeclamp 173 Single Swivel Combination
Single inline swivel connector. Typical use is on sloping guardrails. This fitting combines 1 x 173M & 1 x 173F.
AN ENTIRE STRUCTURE SHOULD NOT BE BUILT USING SWIVEL FITTINGS ONLY
£4.67 |
|
| |
.jpg)
.jpg)
.gif)
.gif)
.gif)
.jpg)
.jpg)
